After 2 to 4 layers of wall-boards are up for the rough opening, it is time to install doors and windows. As the doors and windows slide into the keyways of walls, the lower you have to lift them, the better.
Internal doors
Important: Internal doors come with the bottom packing support. It’s just for shipping. You have to remove it by taking all screws out.
Internal doors come fully installed into the frames. Again, for easier lifting, take the doors out and install the frames only. Frames will slide into the keyways. Adjust it so it is square. Leave internal doors out for now and install them back to frames at a later stage.
External doors and windows
Windows and doors flashings (sourced locally)
Important: We strongly recommend leaving the installation of flashings to professionals, as it is important that they are installed correctly. Improper installation can lead to window leaks.
Flashing is a thin, waterproof material used in construction to prevent water from entering a structure, particularly around joints and edges where building materials meet. It is commonly installed around the foundation, windows, doors, meter box and roofs to create a protective barrier that directs water away from these vulnerable areas. By shielding the frames of windows and doors, flashing helps prevent issues like wood rot, mold growth, and structural damage, ultimately maintaining the integrity and durability of the building. Available in materials such as metal, rubber, plastic, or flexible membranes, flashing is selected based on its durability and suitability for specific applications, ensuring that moisture stays outside where it belongs.
You can find detailed drawings of the flashings in the Construction Guide, which is part of the electronic version of your Owner’s Manual.
Weather-sealing doors and windows (sourced locally)
Expert’s tip: Weather sealing can be done at the same time we seal (paint or stain) the door and window architraves because it requires to perform the same steps of removing the architraves and screwing them back on.
Weather sealing external doors and windows is one of a very important steps. In Australia, the most commonly used weather sealing is with adhesive weather seal tape or PEF Rod. You can find these materials in any hardware store.
- Unscrew the architraves.
- Install the weather seal tape around the perimeter of windows and doors. You may want to seal (paint or stain) the back of architraves before you screw them back on. If you want to leave this for later, then follow the steps of sealing the architraves from all sides here.
- Screw the architraves back on (only bottom of architraves; see important points below)
Important: Support the windows from inside when taking off the architraves from outside and vice versa.
Installing external doors and windows
Important
- Determine the internal and external side of the windows/doors. There is a silicon bead that runs all the way on the outside. So you know that is outside of your windows.
- Do not worry about the space left around the windows and doors. It is essential for natural timber movement, expansion, and contraction. Do not try to fill the space! There must be a 5mm cavity on both sides and 40mm at the top. Cavity at the top will lessen as the structure settles down.
- Make a temporary support for tall windows (as in Borealis or Visteca) and doors.
- Only the bottom corners of the architraves should be screwed to the walls to allow for natural settlement. If you screw the architraves all the way up, the screws at the top will prevent the walls from settling properly, potentially causing gaps to form between the wall boards.
Before you get too high, drop doors and windows down into the grooved sides. Then grab a ladder, get a block on top and just slightly tap it down until its fully located on the bottom.
Expert’s tip: Align the doors and windows up the keyways and slide them down evenly. 2 men are required to easily complete this step.
Installing handles of tilt and turn windows
For guidance on handle positions during installation of tilt and turn windows, refer to the How to Operate Tilt and Turn Windows and Doors page. This will help you ensure the handle is positioned correctly to prevent hardware damage.
Find more information below if you’re installing:
- panorama doors or
- installing windows to custom place
Panorama door installation
To put the front panorama doors in, you’ll need a second person because the doors are quite heavy. Holding doors from both sides, you’ll have to manoeuvre them to line up the channels.
Important reminder. When you install the doors or windows, first determine the internal and external sides. You’ll notice there’s a silicon bead that runs all the way on the outside. So you know that’s outside of your windows.
Watch the video below for detailed instructions.
Installing windows to custom place
If you have to install windows in a custom place or decided to add more windows to your cabin that is already built, follow the steps below:
- Firstly, you’ll have to take off the architraves from outside of the window. You can leave the bottom one on.
- Then you need to measure up what the width and height of your window are. Allow 5mm on each side, total 10mm plus, and 40mm on the top. This is very important not to miss.
- Measure up and mark on the wall where you would like to have windows installed.
- Cut the rough opening, pushing the cut-out panels out.
- Lift the window in. You’ll need someone to hold it from the inside.
- then go outside and screw the architraves back on.
If you’re installing 2 windows in one wall, only do one window at a time. If you cut both windows out, the wall in the middle will come out also. So, only do one at a time.
Watch the video below for detailed instructions.
Installing Scandi Cabins and Scandi Homes is a fairly easy and speedy process. Enjoy it, but remember to check the steel rods are going through after every few wall boards up.
Read all important points you have to remember when assembling the walls in the next Step 10. The list of all building steps can be found on the Builders Guide page.